1971 Plymouth Barracuda Convertible 340/416 4 spd

1971 Plymouth Barracuda convertible Additional Info:

PLEASE READ VERY CAREFULLY There are a lot of details and information in the description and I'll be happy to answer your questions if I missed anything. I purchased this car in the year 2000 with a bill of sale, no title, and a State issued VIN tag on the dash. After purchasing I had the Michigan State Police inspect the car and I applied for a title. I received the title with the VIN number on the title matching the dash tag. This is not a salvage title. I do not have the original vin tags. However the factory stamped numbers are on the cowl indicating it is a 1971 Barracuda (B1). The bright blue metallic (B5) paint is the original color of the car as you can see in the pictures before the car was painted and the new floor was installed. And it still retains the original manual transmission hump. The car is currently registered, plated, and insured. I suggest you check with your State for rules and regulations before bidding. I have been working on it since 2000, and have spent thousands of hours to get it to this point. It was painted in 2006 and has been stored in the garage, and was driven for the first time in 2012 since being purchased. The odometer had 67,321 miles when I started working on it. The motor is a 1970 340 block and was completely rebuilt. dyno results were 451 Hp. @ 5700 rpm’s and 502 lbs. of torque @ 4000 rpm’s. I drove it approximately 900 miles over the next few years and I didn’t like the performance so I took the motor back out and installed a set if Diamond flat top pistons and gained one compression point. Compression is now 11.8-1 and it runs on pump gas (92 octane). A new 850 Holley double pump carb replaced the 750 Holley HP. It runs very strong now and I can only estimate the horse power. It is a blast to drive ! At wide open throttle it's like driving on ice through first and second gear. Otherwise the car does handle very well. The car now has just over 69,700 miles and the motor has approximately 1500 miles since the pistons and carb were installed. I have included a detailed list of the engine and transmission components and all the parts used to put the car together. I also included where a majority of the parts were purchased from and some of the part numbers. The car can be used as a street car, used for car shows, or going to the race track. It has 4 drag racing shocks installed and is set up for drag racing. I'm sure it would ride better with a set of gas shocks installed. Body Details After the rear frame rails were installed, the body was mounted on a rotisserie. All of the rust was sandblasted from the shell of the car in 2001. Then the floor pans, trunk pans, trunk extensions, quarter panels, and doors were installed. The welds aren't perfect in the trunk area like they would be from the factory but are strong and rust free. I also did not install the floor or trunk body plugs. The body is very straight and the paint is beautiful. 340 Engine is now a 416 cubic inch small block. 833- 4 speed transmission, NOS Hurst shifter with pistol grip handle, Passon Performance overdrive gear set converts the 8 ¾ rear end with 4.86 sure grip to 3.91 ratio, attached to Doctor Diff axle shafts. Mancini Racing drive shaft loop surrounds the Joint Clutch and Gear custom drive shaft. Factory front and rear sway bars. Custom Weld in frame rail connectors TTI 2 1/2” X-pipe duel exhaust system from the ceramic coated headers to exhaust tips. 3 core aluminum radiator 340 Billboards Road lamp package Dual sport mirrors Factory Tuff wheel and adapter Rallye guage cluster with working clock Power Convertible Top. Power steering Manual brakes front disc Rear drum brakes 11X2 ½” 1971 Plymouth Barracuda Convertible ENGINE 340/416” Stroker motor 1970 340 block Block Bored- 4.070” Zero Deck Height Block Squared Oil crossover tube modification Holley 850 double pumper carb RPM Air gap Intake EDE 14-7576 Edelbrock Aluminum Heads #60779 Mopar head gaskets .028” #MP4120094 Roller rocker arms #360-4SR Comp. Cams push rods #7821-16 Mopar hardened chrome rocker shafts Rocker shaft clamps 360-5C Rocker stud kit Mopar hardened distributor gear drive Carter High flow fuel pump #6270 Rollmaster Double Roller Timing set MSD Distributor #8388 MSD Rev Limiter #8728 (Installed 8/24/16) MSD plug wires 8 mm Blaster 2 Coil High flow water pump #P5249559 Scott Brown Custom Hydraulic Cam shaft 240/252 H12 Hydraulic Lifters # HT2011 Diamond flat top Pistons- #51007-4.070 Volume/ -6.8cc Perfect Circle File Fit Rings K-1 Technologies Forged 4”Crankshaft 340-400EF6F K-1 Technologies H-beam rods DH6123ANPB8 Mopar fluid damper #4528723998 ACL rod bearings chamfered #11-481H Main bearings 12-1344P ARP Main/Rod bolts Mopar High Volume Oil Pump #M72HV Stock oil pan with internally modified baffle Mopar Engine Block Plug kit #PE113BR Engine gasket kit #269340 Denso Alternator and Bracket Kit # DEN 210-0106 (Mancini Racing) Installed May 2014 440 Source High Torque Mini Starter 4 SPEED TRANSMISSION Hemi 833-18 spline 4 speed Mopar NOS Hurst shifter Passon Performance Overdrive Gear Set Gear Stock Overdrive 1st 2.65:1 2.66:1 2nd 1.93:1 1.59:1 3rd 1.39:1 1.00:1 4th 1.00:1 .80:1 Brewers Performance 4 speed linkage Torque shaft Z-bar Clutch pedal to torque shaft rod Clutch fork Transmission linkage levers Poly transmission mount Shifter boot Centerforce Flywheel Centerforce clutch/pressure plate Quicktime Bell housing RM6072 Van's Auto New speedometer cable installed 3-18-17 New 4 speed shifter boot trim ring installed 3-18-17 SUSPENSION Mancini Racing E-body Super Suspension Kit (Moog) All new tie rod ends, sleeves, upper and lower ball joints, upper and lower control arm bushings, idler arm Driveshaft Loop Adjustable pinion snubber Competition Engineering- Drag racing shocks Front #2620 Rear-#2730 Adjustable Leaf Spring Hangers (front side) 8 ¾ Rear end 4.86 Sure Grip Doctordiff E-body 30 spline axle package McVeigh’s Truck Springs Stock springs re-arched with 1 leaf added Factory rear sway bar (OEM) Factory front sway bar (OEM) Joint Clutch And Gear Custom Drive Shaft New transmission Yoke and u-joints Moparts Connection Big block torsion bars Addco Sway bar end link bushings and bracket Auto Value Parts Store Front Disc brakes Rear Drum Brake’s 11”X 2” New brake calipers, brake rotors, brake drums, all rubber hoses, brake adjusters, aluminum master cylinder, and brake hardware kit. Brake rotors and drums were turned, new brake pads, shoes, wheel bearings, seals, and parking brake cable Rock Auto Fuel tank-CR8C Inline Tube 3/8” fuel line 1/4” return line OEM Brake lines CONVERTIBLE TOP Dons Auto Tailoring Installed convertible top, window, well liner, pads, and cables June 3rd 2010 Legendary Auto Interiors Header seal- WS70CBJHS Window Trim clip set-WG71CBJCLIP Pillar post weather stripping-WS70CBJPOST Convertible top white-CT70CBJ02T Convertible glass white-CG70BJ02 Convertible boot white-CB70CJ00017200 Convertible well liner black-WL70CBJ0016100 Carpet- blue-CA70ES06 INTERIOR Year One Anti- rattler clips-PX505 Firewall Insulation clips-MR663 Barracuda Dash pad decal –VC222 Glove box liner-GBM108 Firewall insulation pad-FP01A Seat foam-bucket seats-XA993 Real Time Engineering Clock Rebuild New Clock Knob Tachometer Board-M4R0 S/N 1596 Factory Rallye Guage Cluster Country Corner Upholstery Custom made front seat covers white Advantage Upholstery Custom made rear seat covers white Custom made sun visors white Convertible Service Nylon hose assembly H43X43N90 Deutschman Automotive Blue floor mat set Door sill plates Herb’s Auto parts 1971 E-body blue seat belt set #2850-71CONBL OEM Panels Door panels black/painted blue Rear panels blue/painted blue Kick panels black/painted blue UNDER HOOD Deutschman Automotive Under Hood pad Battery Hold down Dante’s Wire strap kit-USK04 R/T Specialties Trim clip set-6002976S Grille retainer-3443220 Parking brake pad-1501006 Brake pad, clutch pad-2950887 Gas Pedal Pad-1501001 Mr. G’s Fasteners Interior screw kit mo-1465 Exterior screw kit mo-1950 Under hood kit mo-404 SMS Auto Restoration Rebuilt door hinges & hood hinges Jules Daddio Mopar rebuilt heater blower motor Mancini Racing Mopar windshield washer bottle Washer bottle hose kit (not installed) MREQEWH8C Aluminum radiator 22” 3 core Custom made fan shroud Fuel tank grommet Starter relay Voltage regulator-77R06285 March Performance under Drive Crank Pulley #10171 Viscous fan pkg-P4120758 TTI 2 ½”Complete exhaust system/X-pipe/coated headers Muffler trunk plates (Hoover Auto Parts) Bill Evans Under hood wiring harness Mopar NOS Ignition starter switch PG Classics New road lamp package with harness, switch, brackets, and bulbs Mega Parts Paint seal kit 128-CH3040 Mirror gaskets 128-CH3030 Convertible top weather stripping 128-ch3400 Quarter window seals 117-VS7M WHEELS & TIRES Front- Firestone Firehawk Daytona 500 245/45/R17 Rear-Nitto 275/50/R17 US Mag Wheels Front-17”X 8” Rear-17”X 9” Wheels and tires installed in June 2014 SHEET METAL MADE IN USA Mid- Michigan Body Parts Trunk pan 160-76R Trunk pan 160-76L Floor pan 160-46R Floor pan 160-46L Rear floor pan right 251-62R Rear floor pan left 251-62L Quarter panel 251-50R Quarter panel 251-50L Rear outer wheel extension 251-29R Rear outer wheel extension 251-29L Rear frame rail right 30” Rear frame rail left 30” Trunk extension right Trunk extension left NOS front valance with NOS ID tag on under side Painted dual sport mirrors Factory rear spoiler with Factory mounting brackets Rallye Hood J&J Production 1971 Cuda weld in gilled fender patch panels Paint Car was painted bright blue metallic on 4/20/2006 Base Coat - Clear coat White 340 Billboard stripe kit Goodmark Bumper New rear bumper and bumper guards Installed June 2015 Year One Reproduction front bumper Installed June 2015 Original Equipment Painted fender mounted turn signal indicators Grille (Excellent condition) NOS Lower grille Power convertible top motor Convertible Top Latches Tail Light Lenses and Trim Side marker lenses and housings Battery tray Dash Pad- One small crack between vin tag and windshield Gas cap Mopar 3 port oil breather Tuff wheel with adapter Factory Antenna (new antenna base) Factory steering box Factory power steering pump Factory Jack Jack stand and hook (painted June 2016) Aftermarket Temperature Alternator and Oil Cluster Glass New windshield New Rear window Both door glass and rear quarter glass are re-used and in good condition. Trim All trim is original and was cleaned and polished The 2 short convertible quarter trim pieces were re-chromed New lower windshield trim Included is a new pair of parking light lenses and a new windshield washer hose kit that have not been installed. New reproduction 1971 Barracuda Operators Manual Nationwide battery #24-700 Installed October-10- 2016 Oil and Oil filter change in November 2016 Brad Penn 20W50 Oil and a Wix filter Front end Alignment September-8-2016 I have most of the receipts and hundreds of pictures from start to present and also a couple videos of the car running. I suggest you come and look at the car before bidding. Serious buyers only ! I do not accept any type of check ! No cashiers check ! No personal check ! No money order ! No delivery of car ! It has to be picked up and Paid in cash. Car is for sale locally. Action may end at any time. No Warranty or Refund https://youtu.be/ezLoby-Yz9o https://youtu.be/qwqm4_i4WoU

On Mar-24-17 at 09:25:41 PDT, seller added the following information:

Sorry for the small letters in the description. I Made them a little bigger and put the parts description back to columns. PLEASE READ VERY CAREFULLY There are a lot of details and information in the description and I’ll be happy to answer questions if I missed anything. I purchased this car in the year 2000 with a bill of sale, no title, and a State issued VIN tag on the dash. After purchasing I had the Michigan State Police inspect the car and applied for a title. I received the title with the VIN number on the title matching the dash tag. This is not a salvage title. I do not have the original vin tags. I suggest you check with your State for rules and regulations before bidding. However the factory stamped numbers are on the cowl indicating it is a 1971 Barracuda (B1). The bright blue metallic (B5) paint is the original color of the car. And it still retains the original manual transmission hump. The car is currently registered, plated, and insured. I have been working on it since then, and have spent thousands of hours to get it to this point. It was painted in 2006 and has been stored in the garage, and was driven for the first time in 2012 since being purchased. The odometer had 67,321 miles when I started working on it. The motor is a 1970 340 block and was completely rebuilt. dyno results were 451 Hp. @ 5700 rpm’s and 502 lbs. of torque @ 4000 rpm’s. I drove it approximately 900 miles over the next few years and I didn’t like the performance so I took the motor back out and installed a set of Diamond flat top pistons and gained one compression point. Compression is 11.8-1 and the motor runs on pump gas (92 octane). A new 850 Holley double pump carb replaced the 750 Holley HP. It runs very strong now and I can only estimate the horse power. It is a blast to drive. At wide open throttle it’s like driving on ice through first and second gear. Otherwise the car does handle very well. The car now has just over 69,700 miles and the motor has approximately 1500 miles since the pistons and carb were installed. I have included a detailed list of the engine and transmission components, and all the parts used to put the car together. I also included where I purchased the parts from and most of the part numbers. 1971 Plymouth Barracuda Convertible ENGINE 340/416” Stroker motor 1970 340 block Block Bored- 4.070” Zero Deck Height Block Squared Oil crossover tube modification Holley 850 double pumper carb RPM Air gap Intake EDE 14-7576 Edelbrock Aluminum Heads #60779 Mopar head gaskets .028” #MP4120094 Roller rocker arms #360-4SR Comp. Cams push rods #7821-16 Mopar hardened chrome rocker shafts Rocker shaft clamps 360-5C Rocker stud kit Mopar hardened distributor gear drive Carter High flow fuel pump #6270 Rollmaster Double Roller Timing set MSD Distributor #8388 MSD Rev Limiter #8728 (Installed 8/24/16) MSD plug wires 8 mm Blaster 2 Coil High flow water pump #P5249559 Scott Brown Custom Hydraulic Cam shaft 240/252 H12 Hydraulic Lifters # HT2011 Diamond flat top Pistons- #51007-4.070 Volume/ -6.8cc Perfect Circle File Fit Rings K-1 Technologies Forged 4”Crankshaft 340-400EF6F K-1 Technologies H-beam rods DH6123ANPB8 Mopar fluid damper #4528723998 ACL rod bearings chamfered #11-481H Main bearings 12-1344P ARP Main/Rod bolts Mopar High Volume Oil Pump #M72HV Stock oil pan with internally modified baffle Mopar Engine Block Plug kit #PE113BR Engine gasket kit #269340 Denso Alternator and Bracket Kit # DEN 210-0106 (Mancini Racing) Installed May 2014 440 Source High Torque Mini Starter 4 SPEED TRANSMISSION Hemi 833-18 spline 4 speed Mopar NOS Hurst shifter Passon Performance Overdrive Gear Set Gear Stock Overdrive 1st 2.65:1 2.66:1 2nd 1.93:1 1.59:1 3rd 1.39:1 1.00:1 4th 1.00:1 .80:1 Brewers Performance 4 speed linkage Torque shaft Z-bar Clutch pedal to torque shaft rod Clutch fork Transmission linkage levers Poly transmission mount Shifter boot Centerforce Flywheel Centerforce clutch/pressure plate Quicktime Bell housing RM6072 SUSPENSION Mancini Racing E-body Super Suspension Kit (Moog) All new tie rod ends, sleeves, upper and lower ball joints, upper and lower control arm bushings, idler arm Driveshaft Loop Adjustable pinion snubber Competition Engineering- Drag racing shocks Front #2620 Rear-#2730 Adjustable Leaf Spring Hangers (front side) 8 ¾ Rear end 4.86 Sure Grip Doctordiff E-body 30 spline axle package McVeigh’s Truck Springs Stock springs re-arched with 1 leaf added Factory rear sway bar Factory front sway bar Joint Clutch And Gear Custom Drive Shaft New transmission Yoke and u-joints Moparts Connection Big block torsion bars Addco End link bushings and bracket Auto Value Parts Store Front Disc brakes Rear Drum Brake’s 11”X 2” New brake calipers, brake rotors, brake drums, all rubber hoses, brake adjusters, aluminum master cylinder, and brake hardware kit. Brake rotors and drums were turned, new brake pads, shoes, wheel bearings, seals, and parking brake cable Rock Auto Fuel tank-CR8C Inline Tube 3/8” fuel line 1/4” return line OEM Brake lines CONVERTIBLE TOP Dons Auto Tailoring Installed convertible top, window, well liner, pads, and cables June 3rd 2010 Legendary Auto Interiors Header seal- WS70CBJHS Window Trim clip set-WG71CBJCLIP Pillar post weather stripping-WS70CBJPOST Convertible top white-CT70CBJ02T Convertible glass white-CG70BJ02 Convertible boot white-CB70CJ00017200 Convertible well liner black-WL70CBJ0016100 Carpet- blue-CA70ES06 INTERIOR Year One Anti- rattler clips-PX505 Firewall Insulation clips-MR663 Barracuda Dash pad decal –VC222 Glove box liner-GBM108 Firewall insulation pad-FP01A Seat foam-bucket seats-XA993 Real Time Engineering Clock Rebuild New Clock Knob Tachometer Board-M4R0 S/N 1596 Factory Rallye Guage Cluster Country Corner Upholstery Custom made front seat covers white Advantage Upholstery Custom made rear seat covers white Custom made sun visors white Convertible Service Nylon hose assembly H43X43N90 Deutschman Automotive Blue floor mat set Door sill plates Herb’s Auto parts 1971 E-body blue seat belt set #2850-71CONBL OEM Panels Door panels black/painted blue Rear panels blue/painted blue Kick panels black/painted blue UNDER HOOD Deutschman Automotive Under Hood pad Battery Hold down Dante’s Wire strap kit-USK04 R/T Specialties Trim clip set-6002976S Grille retainer-3443220 Parking brake pad-1501006 Brake pad, clutch pad-2950887 Gas Pedal Pad-1501001 Mr. G’s Fasteners Interior screw kit mo-1465 Exterior screw kit mo-1950 Under hood kit mo-404 SMS Auto Restoration Rebuilt door hinges & hood hinges Jules Daddio Mopar rebuilt heater blower motor Mancini Racing Mopar windshield washer bottle Washer bottle hose kit (not installed) MREQEWH8C Aluminum radiator 22” 3 core Custom made fan shroud Fuel tank grommet Starter relay Voltage regulator-77R06285 March Performance under Drive Crank Pulley #10171 Viscous fan pkg-P4120758 TTI 2 ½”Complete exhaust system/X-pipe/coated headers Muffler trunk plates (Hoover Auto Parts) Bill Evans Under hood wiring harness Mopar NOS Ignition starter switch PG Classics New road lamp package with harness, switch, brackets, and bulbs Mega Parts Paint seal kit 128-CH3040 Mirror gaskets 128-CH3030 Convertible top weather stripping 128-ch3400 Quarter window seals 117-VS7M WHEELS & TIRES Front- Firestone Firehawk Daytona 500 245/45/R17 Rear-Nitto 275/50/R17 US Mag Wheels Front-17”X 8” Rear-17”X 9” Wheels and tires installed in June 2014 SHEET METAL MADE IN USA Mid- Michigan Body Parts Trunk pan 160-76R Trunk pan 160-76L Floor pan 160-46R Floor pan 160-46L Rear floor pan right 251-62R Rear floor pan left 251-62L Quarter panel 251-50R Quarter panel 251-50L Rear outer wheel extension 251-29R Rear outer wheel extension 251-29L Rear frame rail right 30” Rear frame rail left 30” Trunk extension right Trunk extension left NOS front valance with NOS ID tag on under side Painted dual sport mirrors Factory rear spoiler with Factory mounting brackets Rallye Hood J&J Production 1971 Cuda weld in gilled fender patch panels Paint Car was painted bright blue metallic on 4/20/2006 Base Coat - Clear coat White 340 Billboard stripe kit Goodmark New rear bumper and bumper guards Installed June 2015 Year One Reproduction front bumper Installed June 2015 Original Equipment Painted fender mounted turn signal indicators Grille (Excellent condition) NOS Lower grille Power convertible top motor Convertible Top Latches Tail Light Lenses and Trim Side marker lenses and housings Battery tray Dash Pad- One small crack between vin tag and windshield Gas cap Mopar 3 port oil breather Tuff wheel with adapter Factory Antenna (new antenna base) Factory steering box Factory power steering pump Factory Jack Jack stand and hook (painted June 2016) Aftermarket Temperature Alternator and Oil Cluster Glass New windshield New Rear window Both door glass and rear quarter glass are re-used and in good condition. Trim All trim is original and was cleaned and polished The 2 short convertible quarter trim pieces were re-chromed New lower windshield trim Included is a new pair of parking light lenses, new windshield washer hoses kit, and a new speedometer cable that have not been installed. New reproduction 1971 Barracuda Operators Manual Nationwide battery #24-700 Installed October-10- 2016 Oil and Oil filter change in November 2016 Brad Penn 20W50 Oil and a Wix filter Front end Alignment September-8-2016 I have most of the receipts and hundreds of pictures from start to present and also a couple videos of the car running. MVI 7934 https://youtu.be/ezLoby-Yz9o https://youtu.be/EhloWFTAsN8 Cuda walk around video Cuda leaving Hodges https://youtu.be/ezLoby-Yz9o