LS3 Engine swap 1974 C3 Corvette
| Make: | Chevrolet |
| Model: | Corvette |
| SubModel: | LS3 Engine Swap |
| Type: | Coupe |
| Year: | 1974 |
| Mileage: | 60,210 |
| VIN: | 1z37j4s422505 |
| Color: | Red |
| Engine: | 6.2 |
| Cylinders: | 8 |
| Fuel: | Gasoline |
| Transmission: | Manual |
| Interior color: | Tan |
| Vehicle Title: | Clear |
| Item location: | Santa Ana, California, United States |
1974 Chevrolet Corvette Additional Info:
1974 LS3 Swapped Corvette!!!!
Clean tittle currently registered in California. The car was built frame off.
The car has a LS3 and 6-speed TR6060 from a 2014 Camaro SS that had 30k miles. The car was built to handle over 1,000 HP. Very fast and a fun to drive. I hate to sell it but we recently bought some property and I need the cash to put towards the payment. A lot of time, hard work, and money has gone into this car to get it to where it is at today.
The parts list does not include any of the fiberglassing or labor that went into the LS Swap...
Parts Build List | ||
ENGINE AND TRANSMISSION | COST | |
T&T | TR6060 and LS3 6.2 430hp 420lb tq 30k miles | $ 9,500.00 |
custom image corvettes | Tr6060 crossmember LS3 | $ 265.00 |
Ebay | Engine and trans mounts | $ 67.03 |
MSD | spark plug wires | $ 77.00 |
NGK | NGK Spartk plugsplugs | $ 80.00 |
K&N | K&N oil filter | $ 12.50 |
EBAY | drive by wire (gas petal) | $ 63.99 |
holley | LS3 ENGINE SWAP OIL PAN KIT | $ 478.92 |
GM | accessory belt | $ 29.02 |
EBAY | Catch can | $ 118.73 |
ebay | skip gear sylanoid | $ 54.95 |
Muscle Rods | transmission braket for bushing | $ 51.99 |
holley | holley ecu and wiring harness | $ 2,339.00 |
K&N | K&N Air filter kit | $ 329.99 |
Ebay | Starter sylinoid plug adaptor | $ 11.40 |
Ebay | Alternator pig tail | $ 13.95 |
Ebay | 8 guage starter wire 7ft "84" long | $ 44.83 |
EBAY | LS3 relocation shifter | $ 325.00 |
Wilwood | LS3 Hydroaulic clutch master cylinder clutch kit | $ 368.19 |
Ebay | Shifter knob | $ 20.00 |
Ebay | shifter handle | $ 100.00 |
Driveshafts unlimited | Driveshaft | $ 860.00 |
Ebay | Reverse lock out pig tail | $ 10.00 |
Radiator / Cooling | ||
Ebay | LS3 SWAP WATER PUMP MODICFICATION | $ 82.80 |
brian tooley racing | water plug for engine | $ 12.50 |
Champion | radiator/shroud with fans | $ 479.00 |
Ebay | upper radiator tube | $ 27.00 |
Ebay | steam line tube | $ 17.00 |
Ebay | 1/8 pipe to 1/4 for steam line | $ 5.00 |
Ebay | lower radiator tube | $ 20.00 |
Ebay | 1/8 pepe to5/16for steam line | $ 10.00 |
EXHAUST | ||
MELROSE CORVETTE | LS3 SWAP MOTOR MOUNTS WITH CERAMIC HEADERS | $ 855.00 |
Ebay | header gaskets | $ 29.99 |
FLOWMASTER | EXHAUST PIPING AND CLAMPS 3" PIPE | $ 332.32 |
Ebay | exhaust bung plug | $ 3.99 |
Ebay | Header wrap | $ 40.00 |
Jet | Boom mat kit | $ 398.51 |
Fuel | ||
Holley | Holley EFI 80 GPH fuel pump, Pre Filter, Post Filter, fuel regulator | $ 640.08 |
Holley | Pump end fittings -8an male to 7/8-14 (an10) (adapotor to hose) | $ 41.90 |
Holley | Pro-Lite 350™ Black Hose (10 ft.) | $ 77.90 |
Holley | Straight -8 AN Swivel to 3/8” Male NPT | $ 11.24 |
Holley | Swivel Seal™ Straight -6 Female to -6 Hose | $ 17.46 |
Holley | -8AN Male to 7/8”-14 O-ring Port | $ 15.63 |
Holley | Adaptor hose to fuel injector | $ 33.00 |
Holley | fuel injector connector to hose | $ 26.02 |
Holley | Holley filter mounting bracket | $ 62.20 |
Holley | -6 AN Male to 3/4”-16 O-Ring Port | $ 11.42 |
Holley | Straight 3/8” NPT Male to -6 Hose | $ 34.14 |
holley | 6 TO5/16HARD LINE ADAPTOR | $ 12.49 |
holley | 6 TO 3/8 HARD LINE ADAPTOR | $ 12.49 |
Moroso | Aluminum 3/8 fuel line 25ft | $ 29.95 |
Holley | -8AN O-ring port plug | $ 3.49 |
Holley | -6AN male to -8AN O-ring port adapter | $ 10.38 |
Holley | -6AN male to -6AN O-ring port adapter | $ 8.39 |
Holley | Straight -6 Female to -6 Hose | $ 7.93 |
Holley | Straight 3/8” NPT Male to -6 Hose | $ 15.52 |
Holley | UPGRADE FUEL RAILS | $ 195.91 |
Holley | fuel line tubing clamps single 3/8 | $ 9.59 |
VMS | 0-100 PSI Fuel Pressure Gauge (liquid filled) 1-1/2” Dia. 1/8” NPT | $ 32.95 |
Corvette Centeral | Fuel tank kit | $ 340.00 |
Corvette Centeral | gas cap gasket | $ 3.50 |
Eklers | vented gas cap | $ 28.60 |
Holley | 1 foot -8an nylon fuel line (gas tank to return line) | $ 3.39 |
Eklers | Gas tank overflow hose support spring | $ 11.59 |
Holley | 3/8 vinly coated steel fuel line claps | $ 9.59 |
Ebay | fuel gauge adaptor | $ 12.89 |
Ebay | 6an end hose | $ 13.26 |
Ebay | 6an end hose | $ 13.26 |
Holley | power steering 6an hose 90% fuel rail swivel for both adaptors | $ 12.40 |
Holley | cable wire and resistor for the fuel pump | $ 98.00 |
HOLLEY | 90% angles | $ 60.00 |
Holley | 90% TIGHT FIT ANGLE | $ 14.52 |
Brakes | ||
Eklers | Brake line clamp and bolt kit | $ 12.99 |
Eklers | Rear left Distrobution blocks | $ 19.94 |
Eklers | Rear right Distrobution blocks | $ 13.29 |
Eklers | brake and fuel line return tubing clamps double 3/8 | $ 21.65 |
Corvette Centeral | Brake line line kit "stainless steal" | $ 169.00 |
Corvette Centeral | brake/fuel line bolt and clip set | $ 42.75 |
Eklers | Parking brake guide | $ 9.69 |
Eklers | Brake hose cable set | $ 43.49 |
Eklers | E brake cable | $ 18.99 |
Eklers | brake block clips | $ 4.75 |
Eklers | parking brake cable spring | $ 8.00 |
Eklers | Mikey mouse clips for the e brake | $ 6.00 |
Front and rear cross drilled rotors | $ 150.00 | |
Steering | ||
EBAY | power steering pump, pulley, resivore, line | $ 200.00 |
Holley | power steering 6an adaptor to pump | $ 7.99 |
Holley | power steering 6an adaptor to sylinoid | $ 6.49 |
Flaming River | Steering U Joint | $ 94.92 |
Ebay | Turn signal switch | $ 19.80 |
Corvette Mods | Steering gear box 16:1 | $ 227.99 |
Davis Corvette | Rear Adjustable Tie Rods | $ 99.95 |
Eklers | trailing arm shim set | $ 50.95 |
WHEELS / Tires | ||
Weld | Wheels front 15X7 | $ 379.96 |
Weld | Wheels Rear 15X10 | $ 411.96 |
Futura | Tires front 245/60/15 | $ 189.98 |
Futura | Tires Rear 275/60/15 | $ 203.98 |
Eklers | front wheel bearings and seals | $ 34.61 |
Eklers | front wheel dust cap | $ 22.94 |
Total Build not including labor or actual car cost | $ 21,937.74 |
The car still needs a few things to be finished up: LS compatible gauges, carpet, etc.. has a few paint chips but overall the paint is in good shape. please see pics for details. I can send more pictures if needed.
