1992 Nissan 300zx Twin Turbo 5 Speed

1992 Nissan 300ZX Additional Info:

For Sale is a 1992 Nissan 300zx Twin Turbo 5 Speed
The car went through an extensive rebuild. In the process lots of OEM and aftermarket performance parts where installed. Built engine with lots of power upgrades. Almost immaculate paint job and body work. Very clean interior with perfect dash, carpet and door cards. The car exterior was stripped to bare metal, re sealed with epoxy primer and body work was done to practically perfection. There are only a few rock chips and some paint wear on wear spots. Engine was fully rebuilt, bored and honed to new pistons, decked, rods rebalanced, crank polished. The whole rotating assembly rebalanced with the clutch assemble together. Heads where ported to match the exhaust manifold. Upper intake manifold and lower manifold ported to match with head intake runners ported to match lower manifold. Aftermarket bronze valve guides installed, 5 angle valve job was done on the valves and head. Heads decked. The car HAD a working AC but recently the AC compressor clutch made noise and seized, i took the belt off so the car can run without it. All the components are there just probably needs a new compressor. The car has 170K on the clock but there is nothing left original on the car, all the control arms bushing, ball joints, bearings, transmission, diff are all from a low milage car. All the interior pieces where compiled from clean low milage cars. Car has no rust, it had spent most of its life in California and has been garage kept most of its life.
DRIVETRAIN:

• Rebuilt engine includes: Wiseco pistons, OEM rebalanced rods with APR bolts, balanced and polished crank, clevite bearings, OEM head gasket, ported heads, bronze valve guides, 5 angle valve job, new OEM lifters, OEM timing belt, OEM tensioners, OEM water pump, new OEM oil pump, and all OEM gaskets to seal the engine.
• Aftermarket big cast turbo manifolds
• Z1 GT535R turbos
• Z1 2.5" Intake pipe kit
• Dual MAF intake set up
• Z1 2.5" Intercooler pipe kit
• Z1 FM bit intercoolers
• RobZ 62mm throttle bodys
• Z1 3" downpipes
• Z1 3" to 2.5" test pipes
• HKS Hiper cat-back exhaust
• HKS SSQV4 blow off valves
• APEXi AVC-R boost controller
• APEXi SAFC controller
• Big aluminum radiator
• Big front mounted oil cooler running through oil filter thermostat sandwich plate
• Walbro fuel pump with direct upgraded thick wiring.
• Aeromotive fuel pressure reg
• 740cc Nismo injectors
• NGK Colder spark plugs
• New OEM engine harness
• Nistune ECU
• Specialty Z flywheel
• Specialty Z full face 500lb clutch
• Z1 short shifter
• Z1 single piece driveshaft
• NA rear subframe, diff
• Solid engine mounts

• WedSport SA-60M 18x9 wheels with Hankook Ventus R-S3 265/35 front and 275/35 rear
• Powertrix coilovers
• Powertrix front adjustable camber arms
• Powertrix strut tower bars
• SPL front drop down outer tie rods
• SPL front tension arms
• SPL rear camber arms
• SPL rear toe arms
• SPL rear traction arms
• SPL rear eccentric lockout kit
• Stillen rear and front sway bars
• Energy suspension bushings in lower front and rear control arms
• Poly diff bushings
• Rear subframe collars
• New front and rear lower control ball joints
• Akebono brake calipers front & rear (370Z brakes)
• Concept Z 2 piece front rotors
• Stop tech rear brake rotors
• Steel braided brake lines
• ARP longer wheel studs

• Good dash
• Suede interior trim
• Good carpet, floor matts
• Good condition door card
• New leather shift knob, hand brake, and door trim
• Bride bucket seats reclinable on rails
• Nardi wheel with quick release
• Takata harnesses
• Custom harness bar made by True Focus Fabrication
• Alpine Head unit
• Alpine speakers front and rear
• Alpine 10" subs in Zenclosures boxes
• Kenwood 4 Channel AMP and mono AMP
• Sound deadening material installed on doors and rear trunk.
• Stillen front bumper
• Stillen side skirts
• Custom front splitter that attaches to the chassis
• Z1 engine undershroud
• Custom air guides for big intercoolers and radiator
• Custom front wheel well splash guards
• Kaminari FRP rear wing
• Kuruma Z door, quarter glass windshield and t-top new moldings
• New OEM quarter glass trim
• New front and rear glass trim