1992 Mazda RX7 Type R JDM RHD

Make:	Mazda
Model:	RX-7
Year:	1980
Mileage:	78000
VIN:	FD3S-114381
Vehicle Title:	Clean
Item location:	Green Cove Springs, Florida, United States

1980 Mazda RX-7 Additional Info:

Car is a 1992 with chassis number FD3S-114381, it is titled in FL with this number. Ebay requires a 17 digit vin for 1981+, it does not have a vin just the chassis number.
Buy it now includes unpainted shine auto feed replica front end and hundreds to thousands worth of any extra RX7 stuff I have.

1992 Silverstone Metallic over black interior Type R. For those unfamiliar, this is similar to the USDM R1. It has dual oil coolers, came with the front strut bar, spoilers, etc.
Clean/clear title in my name.
78xxx miles, cluster was converted from km's using guides found on rx7club. No cluster swaps. Speedo still has km/h on it, but it has been adjusted to use those marks for mph.
~20k miles on FEED/Fujita Engineering Nur Spec rebuilt engine, exact mileage is unknown but going off of blog entries by previous owner this should be pretty close. I've seen and taken a picture of their engraving on the center iron proving its the same engine. Still has OMP and its been using premix as well in my ownership.
Car runs really good. No issues with starting ever, hot or cold. I haven't done a compression test as I haven't felt the need. I have a piston tester or you can bring your own.
Issues
-Car jumps up and down about 50rpm at warm idle, has done this since I got it.
-A/C system is complete, and was working. I think the over pressure valve on the compressor may have blown out. I'm pretty sure I over filled it. I have another compressor to go with. Complete R134 system.
-Some small dings, bigger dent in left rear quarter, and left side rocker was repaired then painted over.
-I would have someone check the tune since ive added the bigger secondary injectors. I changed the injector settings and it seems to run great but just for peace of mind.
-Missing rear seat (or bins), trunk area carpet, and rear most hatch plastic piece. I have the LRB rear interior kit that can be included.
-I had the car aligned before the new wheels were put on, I ended up lowering the front end a hair so it could use another.
-Holes in hatch for factory wing, then outer ones for a GT wing. Would be covered by a 99 spoiler which was my plan.
-Antenna removed, hole still exists.
Engine
-FEED rebuild. Includes their porting, not as big as a street port from what I have found.
-Apexi Power FC, tuned by FEED
-FC Datalogit
-IRP Water pump and all new Mazda hoses throughout changed Nov 2018.
-Koyo N- Flo Radiator
-RE Amemiya AST
-HKS V Mount
-Efini/99 Y Pipe and Crossover Tube
-Rotary Performance Secondary Rail with Bosch injectors
-Full Function Engineering Air Pump Delete pulley (still have air pump if wanted)
-HKS RS Intake, newish filters.
-FEED Sonic Downpipe
-FEED midpipe and exhaust
-FEED plug wires
-FEED Oil cap-Blitz Super Sound BOV

Driveline
-Exedy Compe R twin disc clutch, installed at time of rebuild. Clutch operation is great, a little noisy due to the nature of the twin disc.
-RE Amemiya shift collar
-Cusco 2 way LSD, again, works great, a little noisy due to the nature of a 2 way diff. I believe this can be opened and swapped to a 1 or 1.5 way with no extra parts.
-4.30 rear end
-solid differential mounts
-Banzai diff brace uninstalled
Suspension/brakes/wheels
-HKS Hipermax II Coilovers w/swift 18kg and 16kg springs
-P2M rear toe arms
-J Auto rear pillow balls
-Super Now front tie rod ends
-Super Now Front sway bar mounts
-FEED Front Strut bar
-OEM 17"/RZ/Spirit R Front brakes, probably the rear also but haven't measured.
-Dixcel slotted front rotors
-Craft Company drilled rear rotors
-EBC Green pads all around
-Advan TC4 18x10 +25 x4
-Firestone Indy500 265/35x4
-Project Mu floating lug nuts
Interior
-NRG quick release
-Momo Race steering wheel
-FEED shift knob
-Redline goods shift and ebrake boots
-Updated to textured panels minus HVAC and door plastics.
-FEED black floor mats
-Bride Zeta III Large w/rail, has a rip on bolster covered by bride pad. Another small one was repaired. Have an OEM driver seat to go with.
-Levy Rotor Corp gas and dead pedals
-Defi Racer 50mm boost and coolant temp gauges
-Innovate Wideband
Exterior
-99 Tail Lights
-FEED Front fenders and bumper. Genuine pieces are the silver ones that are pretty beat, car currently has new shine auto items installed. Both included.
-Group A FEED style hood. factory hood included
-Car Shop Glow v2 attack front bumper lights. Also have FEED lights to go with car.
-Sonar headlights with Morimoto Mini H1 HID projectors retrofitted
-Shine auto FEED style carbon side skirts, no extra holes drilled into car.
-Craft Company Rear diffuser
-Rear wiper deleted, aluminum color matched plug in its place.