1990 Eagle Talon TSi AWD 1g DSM

Make:	Eagle
Model:	Talon
Type:	Hatchback
Trim:	TSi
Year:	1990
Mileage:	144000
VIN:	4e3ct64u3le154481
Color:	Black
Engine:	2.0L
Cylinders:	4
Fuel:	Gasoline
Transmission:	Manual
Drive type:	AWD
Interior color:	Black
Vehicle Title:	Clear
Item location:	Saint Paul, Minnesota, United States

1990 Eagle Talon TSi Additional Info:

It's time for me to sell my project car. I have been working on this 1g AWD Talon since college and I put a lot of time and money getting it to where it is today. As you can tell, I focused on restoring the functional components of the car first, and I haven't gotten as far as I wanted to on the body. If cosmetics are important to you, some time will need to be invested in restoring the body components (some rust removal (see pictures), new paint, etc.)
The engine has been rebuilt and only has a couple of miles on it from tuning the software. The front suspension has been sand blasted and wearable parts have been replaced (I did not get to rear suspension yet). The interior has new carpet, race seats, and new headliner.
This is the perfect car for someone looking for a jump start on a new project. However, this car will run great with more ECM tuning and an alignment. I would not recommend driving the car until it's fully tuned. I have about $9000 in parts into this car, but I'm not looking to get all of that money back, so I'm going to start at $8000 obo.
100% non-smoking vehicle and has a clean title! Serious buyers please. This car is sold as-is and I can provide more info upon request. Buyer is responsible for picking up the car or shipping arrangements. Please notify me 48hrs in advance before picking up the vehicle.
See below for a complete list of mods.
Mods:
Engine Head
o Machined head gasket surface
o Machined valves seats
o Brian Crower Stage 2 Cams - BC0101 272 Spec
o Cometic Head Gasket .051" Thick 86mm Bore - C4234-051
o ARP Head Studs - 207-4201
o Forced Performance Exhaust Manifold Stud kit
o Stainless Steel Valves
o Viton Valve Stem Seals
o Bronze Valve guides
o Revised Lifters (Larger oil passage hole)
o Crower titanium valve retainers
o Crower valve springs
Engine Block
o Bored and honed cylinders
o Machined head gasket surface
o Crankshaft journal bearings reground; Re-Nitride hardening
o Wiseco Pistons - 8.3:1 85.5MM
o ACL Race Main Rod Bearings
o ARP Main Studs - 207-5401
o Crankshaftdepot H-Beam Rods
o ARP Rod Studs
o Mitsubishi Balance Shaft Eliminator Kit
Intake
o DeJon hard intake pipe
o GM 3.5" MAF sensor
o Tial BOV (Version 1)
o 4" turbo intake tube
o AEM 4" Dryflow air filter
o Xo2 Front Mount Intercooler
o Custom aluminum intercooler piping
Exhaust and Turbo
o Holset Hybrid Turbo
 - 4" inlet
 - 1g DSM exhaust turbine housing
 - Welded wastegate port (external wastegate setup)
o Stainless braided oil feed and return lines
o SBR Cast Exhaust Manifold w/ wastegate port
o Tial 44mm Wastegate
o Megan Racing Stainless o2 Housing - MR-TO-DSM
o Megan Racing Stainless Downpipe - MR-SSDP-ME89GSX
o Megan Racing Stainless Test Pipe - MR-CC-ME89GSX
o Thermal R&D Cat Back Exhaust (modified to be 3" diameter to the test pipe)
Engine Misc
o Unorthodox Water Pump, Alternator, and Crankshaft Pullies
o Gates Racing Timing Belt
o New idler and tensioner
o Gates Race Micro-V Belt - K040384RB
o New Alternator
o Allstar breather tank
o New battery (2018)
Transmission
o F1 Racing Prolite Flywheel
o Clutch (car came with this clutch. I believe it's an ACT clutch with a street disc, but I can't confirm)
o Stainless braided clutch line
o New clutch master cylinder
o New clutch slave cylinder
- I have an extended rod if it's needed
o New front axles
o Bronze shifter base bushings
Fuel
o Walbro 255 Fuel Pump (in tank)
o Stainless braided fuel feed line
o FP Labs Fuel Pressure Regulator
o Delphi 850cc injectors (two extra included)
Suspension
o New Beck Arnley Inner Tie Rods - 101-4257
o New Beck Arnley outer tie rods - 101-3904
o MOOG Front Lower Ball Joints - K9617
o Energy Suspension Complete polyurethane suspension bushing kit (rear not installed yet)
o Energy Suspension polyurethane motor mount bushing kit
Brakes
o Remanufactured rear calipers (2018)
o New brake rotors and pads (all four tires)
o New Dorman parking brake cables
Cooling
o GODSPEED Radiator w/ 2x 12" Slim Fans
- Wired to work with stock harness
o Hayden Remote Oil Cooler
o Silicon Upper and Lower Radiator Hoses
Interior
o New Carpet from StockInteriors.com
o Ralliart Mesh Fabric Race Seats
o 5-point harness (not installed)
o Triple Pod A-Pillar
o Clutch Pedal assembly
- New bronze bushings
o Welded clutch pedal assembly
Electronics/Electrical
o ECMLink V3
o Stock ECU w/ ECMLink EPROM Mod and new Capacitors
o AEM Tru-Boost Gauge - 30-4350
o AEM Wideband O2 Gauge - 30-4100
o AEM Oil Pressure Gauge - 30-4407
o NGK spark plug wires
o NGK spark plugs (+1 cold plug, I think)