/ /

1975 Triumph TR6, restored w/S2 mods, beautiful car. Located in NW Connecticut.

Make: Triumph
Model: TR-6
Type: Convertible
Year: 1975
Mileage: 12,000
Color: Pearl White
Cylinders: 6
Fuel: Gasoline
Transmission: Manual
Drive type: RWD
Interior color: Brown
Drive side: Left-hand drive
Vehicle Title: Clear
Item location: Colebrook, Connecticut, United States

1975 Triumph TR-6 Additional Info:

Thanks for checking out my ad.
Here is my beloved TR6, up for sale. She's been through a complete restoration in 2004 and runs great. Lots of S2 mods. A real looker ... and powerful ... and she sounds like few other TR6s. Always stored in a humidity controlled garage, and I always stored her indoors in a Car Bubble from November to May. She's only seen rain a handful to times since 2004. No rust whatsoever.
Details:
Completed restoration in 2004
12,000 miles since restoration
Custom pearl white paint by Phobos Hot Rods
1972 engine rebuilt to 175 HP by Bells Corners British Automotive
Complete disassembly
Frame hot-dip galvanized
Frame epoxy painted and Waxoyl injected
Engine rebuilt to Triumph S2 Fast Road Specs
Complete stripdown, every part removed
Magnafluxed the block, heads, crank, rods, etc.
Flowed, shaved, ported, and polished cylinder head
Rods peened and polished, fitted with ARP high-strength rod bolts
Hi-perf Timken bearings installed throughout
Rings perfect on original, not oversized, so matched and replaced
All components shot-peen and/or nitride hardened
Modified to 10.5:1 compression per S2
Exhaust valve seats hardened / modified for unleaded fuel
Valve seals installed (from Chevy V8; not designed into stock engine)
Emissions equipment removed
Engine balanced, dyno'd 178 HP @ 4500 rpm (stock is 104-125HP)
Lightened flywheel
Piper fast road high performance cam
Longflow racing exhaust header
Aluminum valve cover, polished
Alternator rebuilt + housing polished by C.A.R.
Water pump rebuilt + housing polished by C.A.R.
Starter rebuilt by C.A.R
Distributor rebuilt by C.A.R.
Carbs: original Stromberg Zeniths rebuilt +w/ S2 needle valves
New oil cooler w/custom brackets and braided stainless steel lines
Spin-off oil filter mod and remote-located mount w/oil cooler fittings
High-performance Longflow intake filter set
Monza dual exhaust w/resonators
Rebuilt tranny
High-performance racing clutch
Radiator re-cored and painted
New air box shroud
Fuel tank sandblasted and epoxy sealed, in and out, and painted stock black
Rebuilt frame on rear end to strengthen to S2 specs
Diff pins boxed to S2
Differential rebuilt to S2
New front springs and shocks
Rear suspension rebuilt by C.A.R., sandblasted, painted
All new rubber parts front and rear
New aluminum racing rack and pinion steering mounts
Rebuilt steering assy
Hubs rebuilt, new high-performance Timken bearings
Panasport wheels
Electrical harnesses removed and professionally rebuilt to factory specs by TRF
All new Lucas bullet connectors
New frame and top
Custom cherry steering wheel
Rollbar bolted through frame w/SS backing plates
Installed fire extinguisher
Custom-made hinged Lexan windscreen nested in rollbar
Installed TRF secondary bonnet release lever
New hydraulic clutch master and slave cylinders and plumbing.
PM regarding your interest.
Additional photos on request.
Available for inspection in Northwestern Connecticut.
Kind regards!
==
Additional Notes:
The S2 Spec is based on a series of cams from stock S1 through fast road S2 through racing S3 S4. The S specs were designed by Kas Kastner and the British Leyland / Jag-Rover-Triumph Competition Department. Primary sources are Competition Preparation Manual for TR-250/TR6 and Kas Kastner's Spitfire, GT-6, TR-3, TR-4, TR-250, TR-6 Triumph Preparation Handbook.